When adding the keypad to your gateway, you can use the web or mobile app. RED FLASHING: If the status indicator is flashing RED every 4 seconds, the abode system is in the alarming/ triggered mode. The Occupancy Sensor will also be available for usage as a Trigger for CUE automations (e.g. It's correct; I did just set off the alarm. When the system is in standby mode and there is no issues, the LED on the face of the gateway should remain off. But how … This fault could be a number of problems: The internet connection could be down. The Keypad will add to your system as two devices— a Keypad and an Occupancy Sensor. To disable this features hold down the 4 + 6 keys for 3 seconds. When the battery is low, a low battery alert will be sent to your gateway, and red LED will blink on the Keypad twice every 60 seconds. Most false alarms occur when the user enters the home not knowing that the system was armed. Sounds can be re-enabled hold holding down the 7 + 9 keys again for 3 seconds. Motion detection is enabled by default on the Keypad. The device will show up in your device list, select Add and follow the wizard to complete the pairing process. Pairing the Keypad With Your Abode Gateway. 2. To arm a certain type of alarm via your abode keypad, use the following instructions: Panic Alarm (if enabled) -press both 1 and 3 for 3 seconds. The alarm function may be added in the Abode web app. The Keypad has a built in quick-arm feature that allows users to arm the system with one button press. On the back of the keypad, in the bottom left corner, is a hard reset button. If only one devices shows, press and hold the pairing button until the app continues. The Occupancy Sensor can be used to activate alarms or to trigger CUE automations. The Occupancy Sensor will also be available for usage as a Trigger for CUE automations (e.g. Find Add Device menu (on your abode dashboard or in the settings of the mobile app), select the Keypad 2 option and follow the instructions to add the keypad into your system. Note that disabling the motion detection will also disable motion detection for alarms and CUE automations. If there are 5 incorrect attempts within 10 minutes, the Keypad will disable for 5 minutes for security. If movement is detected by the motion sensor, the backlit keys of the Keypad will light up. Cover- Screw (Access function button and battery), After paring the status indicator with the gateway, check the web app to insure the status indicator has been included into the device list. If pairing is not successful, please use the "other devices" method of "add device. * if you do not see this as an option, please contact support as you may need an updated firmware. Note that completing a factory reset will not unpair the Keypad from your gateway, but will force the Keypad to restart and delete any presets (such as motion sensing having been disabled). Find Add Device menu (on your abode dashboard or in the settings of the mobile app), select the Keypad 2 option and follow the instructions to add the keypad into your system. Inside the entry exit points of the home so that before you open that door to walk the dog, you will be aware that the system may be armed. As a result of this change, adding SOME system indicators needs to be done from the "other devices" menu option). The code may be re-attempted after the 5 flashes. For ideal motion detection, mount the Keypad on a wall about 4.5 feet above the ground. By default, the Occupancy Sensor will not be setup to activate alarms when your system is armed. First mount the magnet to your preferred location using the included screws or adhesive strips, then clip the Keypad directly to the magnet. Pairing the Keypad With Your Abode Gateway . Disarming the system will turn this RED Flashing LED off. The included screw anchors may be used for drywall, plaster, or brick surfaces. "*, (*We recently changed our system status indicators to utilize abode RF where they previously using Zigbee. The perfect addition to your system, our new & improved keypad features a built-in motion sensor to alert you to your system status every time you walk by, backlit buttons for easy low-light arming and disarming, and more. The system status indicator has been designed to help prevent user errors and to reduce false alarms. By default, quick-arm is enabled. Once instructed, insert the battery into the device then press the “Pairing” button several times on the inside of the sensor until you see the device show up on the app as detected. The occupancy sensor is capable of detecting motion with a 90 degree coverage at up to 3 meters. By default, the Occupancy Sensor will not be setup to activate alarms when your system is armed. My Keypad 2 is slowly blinking red and white, which indicates that there was a "recent fault." In the Add Device dialog, select the proper device from the list and follow the wizard. Keypad key press, door open, and countdown timer sounds may be disabled by holding down the 7 + 9 keys for 3 seconds. For first time use, it is recommended to let your Keypad charge for at least 4 hours using the included Micro USB charging cable and a 5V USB port. With a paperclip, hold this button down for 10 seconds to factory reset the keypad. When a bright red LED is flashing, the system has been triggered and is in the Alarm mode with sirens activated. Note that by default the Keypad motion sensor will not trigger an alarm when your system is armed. This event will be listed on the timeline, and a fault reminder will show when the system is armed. The low battery event will show in the timeline and a fault reminder will show when the system is armed. Quickly change the status of your abode system: Away, Home, Standby, USB rechargeable battery lasts up to 6 months on single charge, 40 user codes controlled using the abode web app, Use motion detection for alarms and CUE automations, The Keypad will add to your system as two devices— a Keypad and an Occupancy Sensor. The Keypad will pair in as two devices— a Keypad and an Occupancy Sensor. Tamper on the keypad or one of the devices could be triggered; To check for system faults, review the timeline of events on the web or mobile app. While the Keypad is charging, the green LED will be solid. Pairing the Status Indicator into the Gateway When pairing the status indicator to your gateway, you will need to use the abode web app. When battery charge has been fully restored, the green LED will turn off. An offline or device missing event notification should be listed on the timeline and a fault reminder will show when the system is armed. Future app updates will allow user to program the Triangle and Square buttons to perform up to four unique functions or scenes. One of the devices may have lost its wireless communications with the gateway.