The Honeywell 997 ceiling mount motion detector is the ideal solution for hardwired security systems that require a motion sensor in a central location that is not easily recognizable as a security device. If absent at terminals (andPulse Count: 1- or 2-event, installer-selectable. The compact, discrete size makes it a nearly invisible way to detect motion, so it will not detract from the style or architecture of the protected area. Série 9 Polyvalent, Exceptionnel, Parfaitement conçu Le dernier kit carillon qu'il vous faudra acheter. 6. KNOCKOUTS (2) B. Passive Infrared Motion Detecting Sensors, Honeywell PIR Motion Detector Comparison Chart. R7999A,B CONTROLINKS™ CONTROLLER 65-0238—10 4 Table 1. Optimum Mounting Orientation Detection Area In order to maintain the detector in proper working condition, LED ENABLE/DISABLE it is important that the following be observed by the user. Solid state flame sensing circuit External button to manually reset safety switch after lockout Includes 40 VA transformer and Y and G terminals for connection of cooling equipment Mounts on standard 4 x 4 in. 3. protected area cleared of all people. Loss of power HEIGHT HEIGHT to the unit will result in the alarm contacts reverting to an (3.66m) (2.4m) enable/disable plug in place). "OFF"Current Drain: 17mA. Mounting the detector on the ceiling helps minimize vandalism and tampering—making it especially effective in public areas such as schools and retail establishments. And if your ceiling is greater than 12 feet high, then you probably shouldn't use the Honeywell 997 in that area. c. If using serial devices, attempt to manually enroll the serial number. Slideshare uses cookies to improve functionality and performance, and to provide you with relevant advertising. must be enabled at this time (LED jumper plug removed).shown in Figure 1. While a single 997 is ideal for sensing motion in rooms up to 30' x 30', multiple detectors are recommended when protecting larger areas like classrooms, meeting rooms, public lobbies and storage areas. As a wired sensor, you will need to run a wire from the sensor to the panel. endstream endobj 2526 0 obj <>/Metadata 70 0 R/Outlines 110 0 R/PageLayout/OneColumn/Pages 2521 0 R/StructTreeRoot 584 0 R/Type/Catalog>> endobj 2527 0 obj <>/ExtGState<>/Font<>/XObject<>>>/Rotate 0/StructParents 0/Type/Page>> endobj 2528 0 obj <>stream A selectable pulse count allows you to adjust device sensitivity. Pulse Count in the PIR must be “OFF” (jumper plugBest coverage will be obtained if the PIR is mounted such (jumper removed), and set Pulse Count “off” (jumper removed) to provide instant response. If present, checkDetectable event. Power should be provided at all times. Starting with surface mount passive components like resistors and capacitors, then moving to integrated circuits like amplifiers, now even sophisticated microprocessors are surface mounted on ADEMCO's Flexible Manufacturing Lines. Select a location that will provide the coverage desired. No Contract Alarm Monitoring starting at $10 a month! When mounting on the ceiling, ensure that the coverage pattern is largely unobstructed by large items, such as plants, curtains, screens, or large pieces of furniture. (and the alarm relay contacts remain open) for• Do not install where the detector is exposed to direct INTRUDER’S MOST LIKELY DIRECTION OF MOTION approximately 1 to 3 seconds after detecting motion. TO SEPARATE For the latest warranty information, please go to: TO CLOSED CIRCUIT TAMPER CIRCUITINSTALLING AND WIRING THE PIR PROTECTIVE LOOP www.honeywell.com/security/hsc/resources/waThe ceiling on which the PIR is to be mounted must be firm TO 12VDC + POWER SOURCE 997-003-V0and vibration-free.1. 997 Ceiling-Mounted Passive Infrared Motion Detector INSTALLATION INSTRUCTIONSGENERAL INFORMATION 3. If you wish to opt out, please close your SlideShare account. Honeywell Vista Panel Polling Loop Troubleshooting Guide . The tamper terminals (see Figure 3) should A. DC voltage supplied to detector is inadequate, be connected to the control panel’s tamper loop. See our User Agreement and Privacy Policy. zones and that walk-testing is carried out along these routes.Important: Avoid running alarm wiring close to heavy-duty ALARMelectrical power cables. LED enable/disable plug is installed.Voltage: 12VDC nominal (voltage reversal makes one pin when the plug is not in use. When relay contact terminals and check continuity 18-ft (5.5m) radius. Alarm Grid Home Security http://www.alarmgrid.com/ has provided this pdf with the permission and courtesy of Honeywell. Figure 2. (Including Access Control, Intrusion & Video Surveillance), Automated SMD Construction on the Flex Lines. endstream endobj startxref This verifies that the panel is able to talk to the device as well as the proper serial number. Installation manual for the Honeywell 997 ceiling mount PIR motion detector. protective zones, observing that the PIRs LED lightsPulse Count, which provides protection against false alarms, Important Note: Optimum mounting orientation is shown in whenever motion is detected (the LED serves as a walk-and an LED enable/disable feature (installer-selectable). Installation manual for the Honeywell 997 ceiling mount PIR motion detector. Testing should be conducted with theefficient protection pattern for commercial and residential wires do not obstruct the detector’s field of view. Scribd will begin operating the SlideShare business on December 1, 2020 h�b```b``6f`a`�� Ȁ ���@q���"E�L��v3dj��0��`�ݨ����2@�Ť����Aږ�p�8���6u��� ɥ9P {2T4@ ������F� C(��B�UZ̷��]�� ��Q����H��������L�XND� ``T����9r/cc�j�]ċ�,�@���!�H1�T͆��4�3��ˏ\��@$` �;L# Good: Twist-Off Cover, Walk Test LED, Cover Tamper, Bad: Coverage Area Determined by Ceiling Height, Requires Wiring, Draws Power. 7. DET OFF "ON" LED WITH PLUG Remedy: Caution customer about layout changes.Operating REMOVED.Temperature: 32°F – 122°F (0°C – 50°C). LEDStandby "OFF" WITH ON LED PLUG A. With the cover installed on the PIR, walk through theThe Detector features installer-selectable Alternate Polarity the screw holes provided in the base of the PIR. Rapid temperature change. Honeywell 997-install-guide 1.